

 If you are going to use Windows NotePad to print this Q_A.TXT,
 you will have to go under <File>, <Page Setup>, and set <Left>=0,
 <Right>=0, <Top>=0, <Bottom>=0.

                     FAQ (Frequently Asked Questions)
 COMTEST1.COM and COMTEST2.COM-----------------------------------------  1
 Fax/Modem-Driver not loading------------------------------------------  2
 FaxMail for Windows does not run or does not run properly-------------  3
 None of the Fax/Modem-Drivers work------------------------------------  4
 I set the sound/volume/retries but my Fax/Modem ignores my changes----  5
 Fax/Modem-Driver didn't even attempted to load from my AUTOEXEC.BAT---  6
 This Function requires a Fax/Modem-Driver before entering Windows-----  7
 I do not know what kind of Fax/Modem I have---------------------------  8
 I tried the Fax/Modem-Driver that was suggested for my Fax/Modem, but-  9
 ElectraSoft Fax phone number (713) 499-5939,11,11,11,11 did not work-- 10
 I can FAX but can not print------------------------------------------- 11
 Computer keeps asking if I want to allow writing to FM_DS_IN.CFG------ 12
 More than one FaxMail for Windows "Control" Windows StartUp group----- 13
 I am prone to losing dialog-boxes behind other boxes and windows------ 14
 "Pulse" or "Tone" Dial-Out-------------------------------------------- 15
 Fax came out of my Printer blank-------------------------------------- 16
 FaxMail for Windows Cover-Page width---------------------------------- 17
 When building a Cover-Page; Where should I put the Logo?-------------- 18
 Why couldn't <PRINTER OR FAX TOGGLE> be done automatically?----------- 19
 My Fax/Modem hangs up during send/receive----------------------------- 20
 <CONVERT TO FAX> doesn't work from some of my programs---------------- 21
 FM_ROCK1.COM works on one computer but not on another identical one--- 22
 I ran COMTEST1.COM and COMTEST2.COM.  What does the <O>s and <I>s mean 23
 COMTEST1.COM and COMTEST2.COM produce only <O>s----------------------- 24
 Digicom Connection 14.4+Fax or P. C. LOGIC FAX144C, FAX144DM---------- 25
 My GVC, FM-144HVBIS/R1  V1.61, won't work properly-------------------- 26
 My "Supra FAX Modem" does not work right------------------------------ 27
 My "HP Deskjet 500C" takes 30 minutes per page to print a Fax. !HELP!- 28
 Word for Windows 2.0 sometimes shifts the image to the far right------ 29
 Windows Write sometimes crashes when I try to <CONVERT TO FAX>-------- 30
 Does the FaxMail for Windows Fax/Modem-Driver LH (LoadHigh)?---------- 31
 Windows keeps asking if it should take control of Fax/Modem COM?------ 32
 My Modem seems to have some sort of conflict while in Windows--------- 33
 List of Fatal Error Code meanings------------------------------------- 34



 QUESTIONS AND ANSWERS:
 Q-1
  I ran COMTEST1.COM and COMTEST2.COM and read the CLASS1.TXT and
  CLASS2.TXT files that were generated.  What does all that "gibberish"
  mean?

 A-1
  <O> mean OUT to your Fax/Modem.  That is the way FaxMail for Windows
  talks to your Fax/Modem.

  <I> mean IN from your Fax/Modem.  That is the way your Fax/Modem talks
  to FaxMail for Windows.

  Typical dialog between FaxMail for Windows and your Fax/Modem follows:

 <O> AT+FCLASS=?  }FaxMail for Windows to Fax/Modem; What Class are you?
 <I> 0,1,2        }Fax/Modem to FaxMail for Windows;
                  }I am Class 0 (Data,BBS), Class 1 Fax and Class 2 Fax.

 <I> OK           }Means your Fax/Modem supports said function.
 <I> ERROR        }Means your Fax/Modem does not supports said function.

 Q-2
  When I am booting and while my AUTOEXEC.BAT is loading I hear two BEEPs
  and the Fax/Modem-Driver says it is not loaded.

 A-2
  If your Fax/Modem is turned-off or hung, or the Fax/Modem-Driver you
  chose is not compatible with your Fax/Modem or computer, the
  Fax/Modem-Driver will make a BEEP and fail to load.

 Q-3
  FaxMail for Windows does not run or does not run properly.

 A-3
  If you are currently using another Fax-Program, you will have to
  disable or remove it before using FaxMail for Windows as two
  Fax-Programs can not share the same Fax/Modem or run concurrently.



 Q-4
  None of the Fax/Modem-Drivers work.

 A-4
  Be sure you have the latest Version.  FaxMail for Windows is being
  updated continuously.  We may have a new Fax/Modem-Drivers that will
  work for you.

 Q-5
  I set the sound/volume/retries but my Fax/Modem ignores my changes.

 A-5
  The DoveFax and some other Fax/Modem do not support volume and
  speaker manipulation.

 Q-6
  I did the INSTALL.EXE and re-booted, but the Fax/Modem-Driver didn't
  even attempt to load from my AUTOEXEC.BAT.

 A-6
  FaxMail for Windows put a Fax/Modem-Driver in your AUTOEXEC.BAT.  Look
  in your AUTOEXEC.BAT and see if you have a menu or jump command ahead of
  the Fax/Modem-Driver.  If you do, move the Fax/Modem-Driver to a place
  in your AUTOEXEC.BAT where they will load, preferably, first.  The
  Fax/Modem-Driver looks something like this:

 C:\FAXMAIL\FM_ROCK2.COM

  NOTE: If you are using the FaxMail for Windows Dynamic All Class
  Fax/Modem-Driver, there will be nothing placed in you AUTOEXEC.BAT.



 Q-7
  I removed or commented the Fax/Modem-Driver from my AUTOEXEC.BAT and
  now when I try to run ant Windows program that has a print-routine in
  it, I get a message saying:

     This Function requires a Fax/Modem-Driver to be
     loaded before entering Windows.

     1. Did you re-boot after installing FaxMail for
        Windows?  If not, re-boot the computer now.

     2. You may have to use the FaxMail for Windows
        Change Fax/Modem-Driver command and install
        a different Fax/Modem-Driver.

 A-7
  If you had a power failure while in Windows or you crashed out of
  Windows while FaxMail for Windows was active, your
  Default-Printer-Driver may have been replaced with the FaxMail for
  Windows Fax-Converter ("FaxMail Fax/Modem-Driver").

 Solution:
  Close the FaxMail for Windows "Control" Program by clicking on the
  <System> button, <QUIT> button.  Load the Windows Control Panel
  (found in "Accessories" Group or "Main" Group), select Printers and
  choose the Printer-Driver that you want as your Default-Printer-Driver.
  Then reload the FaxMail for Windows "Control" Program

 Note:
  When you have the FaxMail for Windows Control loaded and the PRINTER OR
  FAX TOGGLE is toggled to FAX, Windows swaps from your Default-Printer-
  Driver to "FaxMail Fax/Modem-Driver".  When you toggle back to
  PRINTER or exit Windows, Windows swaps back to your
  Default-Printer-Driver.  If you crash out of Windows, Windows does not
  get a chance to swap back, so the next time you enter Windows it thinks
  that "FaxMail Fax/Modem-Driver" is your Default-Printer-Driver
  and when FaxMail for Windows makes it's swap it swaps
  "FaxMail Fax/Modem-Driver" for
  "FaxMail Fax/Modem-Driver".

 Q-8
  I do not know what kind of Fax/Modem I have.  Who made my Fax/Modem?
  I want to know more about my Fax/Modem.  Is it Class 1, Class 2, etc?

 A-8
  Run: COMTEST1.COM and COMTEST2.COM.  They will tell you what CLASS, the
  Manufacturer, the Model number and much much more about your Fax/Modem.
  After running COMTEST1.COM and COMTEST2.COM, you may need to turn your
  Fax/Modem (computer if you have an internal Fax/Modem) off-on and reload
  your Fax-Software.  If you are using FaxMail for Windows COMTEST1.COM
  and COMTEST2.COM sends a signal to the FaxMail for Windows
  Fax/Modem-Driver asking it to re-initialize(reset) your Fax/Modem.



 Q-9
  I tried the Fax/Modem-Driver that was suggested for my Fax/Modem, but it
  did not work.

 A-9A
  Run: COMTEST2.COM.  Test a COM-Port to see if one of the Class 2
  Fax/Modem-Driver may support your Fax/Modem.  COMTEST2 will create a
  written report in the form of a text file called CLASS2.TXT.  If your
  Fax/Modem is Class 2 the report may include the following line:
 This Fax/Modem supports Class 2, Fax Mode.
  and it may also say:
 One of the Class 2 Fax/Modem-Drivers may work with this
 Fax/Modem on this COM-IRQ.

 A-9B
  Run: COMTEST1.COM.  Test a COM-Port to see if one of the Class 1
  Fax/Modem-Drivers may support your Fax/Modem.  COMTEST1 will create a
  written report in the form of a text file called CLASS1.TXT.  If your
  Fax/Modem is Class 1 the report may include the following line:
 This Fax/Modem supports Class 1, Fax Mode.
  and it may also say:
 One of the Class 1 Fax/Modem-Drivers may work with this
 Fax/Modem on this COM-IRQ.

 Notes:
  *The Universal Fax/Modem-Drivers are designed to overcome special
   Problems.

  *If you do not know what class your Fax/Modem is, run both COMTEST1 and
   COMTEST2, as your Fax/Modem can and often is both class 1 and class 2.

  *You should turn your Fax/Modem off-on just before each test.  In the
   case of an internal Fax/Modem, turn your computer off-on.

 Q-10
  I called the ElectraSoft Fax phone number (713) 499-5939,11,11,11,11
  and it did not work.

 A-10
  Call voice (713)-261-0307 first to make sure that it is available and
  not being used for R&D.  BTW, The ,11,11,11,11 tells us to route the
  call to our Fax/Modem.  If you want to call our Computer Technical
  Support (CTS) BBS dial (713) 499-5939 without the ,11,11,11,11.



 Q-11
  I am in Windows and I try to print but the FaxMail for Windows
  FaxMail Fax/Modem-Driver(C:\WINDOWS\SYSTEM\FM_PN_DX.DRV) intercepts the
  print-job and wants to send it to a remote Fax-Machine.

 A-11
  Click on the <System-Button> and then on the
  <PRINTER OR FAX TOGGLE> button.

 Notes:
  *If the <PRINTER OR FAX TOGGLE> button has a check by it and it says
  "FAX IS ACTIVE", then the print-job will be printed on a remote
  Fax-Machine.  If the <PRINTER OR FAX TOGGLE> button is not checked and
  it says "PRINTER IS ACTIVE" the print-job will be printed on your
  default printer.

  *When you toggle the PRINTER OR FAX TOGGLE, FaxMail for Windows swaps
  the Print-Driver found in your WIN.INI form your normal default to the
  'FaxMail for Windows FaxMail Fax/Modem-Driver(FM_PN_DX.DRV)'
  Print-Driver.  So...If the <PRINTER OR FAX TOGGLE> button is set to the
  FaxMail Fax/Modem-Driver ("FAX IS ACTIVE") mode and you re-boot with a
  (press <Alt+Ctrl+Del>), turn the power off-on or power failure, the
  FaxMail Fax/Modem-Driver(FM_PN_DX.DRV) will be left in your WIN.INI
  file.  As a result, toggling the <PRINTER OR FAX TOGGLE> button will
  switching "back and forth" between the FaxMail Fax/Modem-Driver and
  FaxMail Fax/Modem-Driver Print-Driver and your actual default
  Print-Driver will be lost.

 Solution:
  If, or when, this happens, you will have to:
  1. Click on the <System-Button>
  2. Click on the <QUIT> FaxMail for Windows button.
  3. Load the Windows "Control Panel" program.
  4. Load the "Printers" program.
  5. Highlight your normal Printer-Driver.
  6. Click on <Set As Default Printer>.
  7. Click on <Close>.
  8. Load the FaxMail for Windows "Control" program to reload FaxMail for
     Windows back-ground operation again and all will be normal again.

 Q-12
  As I am using FaxMail for Windows, a message keeps popping up; asking
  me if I want to allow the system to write to FM_DS_IN.CFG and the
  FaxMail for Windows Fax/Modem-Driver FAXMODEM.CFG file.

 A-12
  You have a Virus detection program that is not working properly.

 Solution:
  Remove the "Virus detection" software from your AUTOEXEC.BAT and/or
  elsewhere.

 Note:
  The FaxMail for Windows Fax/Modem-Driver and Windows to Fax/Modem-Driver
  Interface both write to configuration(.CFG) files during each session to
  track the ever changing "dynamically-flowing" defaults that make it
  easier for you to operate.



 Q-13
  There is more than one copy of the FaxMail for Windows "Control" program
  in my Windows StartUp group.

 A-13
  If you had to try more than one Fax/Modem-Driver during installation,
  You will have to click once on the extra FaxMail for Windows "Control"
  ICON, click on Files and then click on delete.

 Q-14
  I am prone to losing dialog-boxes behind other boxes and windows.

 A-14
  If you lose a dialog-boxes while using FaxMail for Windows, simple
  reload from button or ICON.  Actually when you try to reload a lost
  dialog-boxes, the new instance detects the old instance and sends a
  message to it that brings it to the top and then does not load itself.
  Because you get back the one you lost, you do not lose any of your work.

 Q-15
  I have pulse-dial-phone and can not get tone dial in my area.

 A-15
  Click on the "SetUp" button and you can select "Tone Dial" or "Pulse".

 Q-16
  I Viewed a Fax but when I tried to Print it, the paper came out of my
  Printer blank.

 A-16
  Be sure your printer is set to Portrait and *not* Landscape.

 Q-17
  When I use the FaxMail for Windows Cover-Page feature; How wide can I
  make it?  And; What about the left and right margins?

 A-17
  No more than 72 characters wide.  You do not have to concern
  yourself with the left or right margin as there is a 3/8" left and
  right margin built into FaxMail for Windows NotePad for you.  This
  will permit compatibility on Fax Machines as well as Fax/Modem to
  Fax/Modem to Printer supports.

 Note:
  Do *NOT* use the <Tab> in the a Cover-Page file (*.CVR).

 Q-18
  When building a Cover-Page; Where should I put the Logo?

 A-18
  Go into the FaxMail for Windows NotePad and open a Cover-Page file
  (*.CVR) and put your cursor on the first line.  Select Fields and Logo.
  Be sure that the <Logo-Field> is on the first line in the Cover-Page
  file, by itself, with no other text on that line.  When the Send-Fax
  program processes the Cover-Page file, it will use the information on
  that line and then remove that line, so your second line will become
  the first.



 Q-19
  When I want to Fax, I have to go to the <System> button and toggle the
  <PRINTER OR FAX TOGGLE> to FAX and when I want to Print to my default
  Printer, I have to toggle the <PRINTER OR FAX TOGGLE> to PRINTER.  Why
  couldn't that be done automatically?

 A-19
  Some Windows applications get a HANDLE to the Printer-Device-Context
  upon entry and when you go to print, they use that HANDLE.  If we were
  to suddenly swap from the default Printer-Driver to the
  "FaxMail Fax/Modem-Driver" Driver, the current application would
  crash when it tried to use the obsolete HANDLE.

 Note:
  FaxMail for Windows does send out a global message to all applications
  every time it swaps from the "FaxMail Fax/Modem-Driver" to your
  "Default-Printer-Driver" or back again, but not all applications pay
  attention to it, so you may have to toggle the <PRINTER OR FAX TOGGLE>
  before loading these applications.

 Q-20
  My Fax/Modem-Driver loads all right but when it tries to send/receive;
  the Fax/Modem hangs up immediately.

 A-20A
  You may have the phone-line plugged into the wrong jack on the back of
  your Fax/Modem.

 A-20B
  You may have to Change Fax/Modem-Drivers.

 A-20C
  You may have a hardware conflict.  If so, call ElectraSoft and they will
  help resolve it.

 Q-21
  I went into a Windows application and tried to send a Fax using the
  FaxMail for Windows <CONVERT TO FAX> option, but the application just
  wants to print to my default printer.

 A-21
  AMI Pro, WordPerfect and some other Windows applications have their
  Printer-Driver information stored in an ?.INI file and are not willing
  to swap their Printer-Driver on the fly.

 Solution:
  Before using the <CONVERT TO FAX> button, go to <Files>,
  <Printer Setup> and choose "FaxMail Fax/Modem-Driver" as your
  Printer-Driver.  Now the <CONVERT TO FAX> will work.



 Q-22
  I chose
  "Universal, Hayes, Rockwell, Class 1 -- FM_ROCK1.COM" the first time I
  installed FaxMail for Windows and everything worked fine.  I noticed
  that when I chose "Hayes" that the INSTALL.EXE used FM_ROCK1.COM
  Fax/Modem-Driver.  Later, I installed FaxMail for Windows on another
  computer, it also had a Hayes.  This time I chose "Universal, Rockwell,
  Class 1 -- FM_ROCK1.COM" because this selection uses the same
  FM_ROCK1.COM Fax/Modem-Driver but it would not work.

 A-22
  When the Fax/Modem-Driver is being installed, it is modified by the
  INSTALL.EXE.  These modifications will differ from one manufacturer to
  the next.

 Solution:
  Select the Fax/Modem-Driver by manufacturer rather than by name and be
  sure to use the INSTALL.EXE to install rather than coping the Drivers.
  If you copy the files onto your HardDrive, FaxMail for Windows will
  not work.

 Q-23
  I ran COMTEST1.COM and COMTEST2.COM.  When I read the CLASS1.TXT and
  CLASS2.TXT files, that they produced, I found that they only <O> to my
  Fax/Modem but did not <I> from the Fax/Modem.  After installation the
  FaxMail for Windows Fax/Modem-Drivers will not load.

 A-23
  <O> mean OUT to your Fax/Modem.  That is the way FaxMail for Windows
  talks to your Fax/Modem.

  <I> mean IN from your Fax/Modem.  That is the way your Fax/Modem talks
  to FaxMail for Windows.

  Check with your Fax/Modem manual and make sure that you know for sure
  which COM-IRQ is selected.  Also check for COM-Port and IRQ Conflicts.

  COM-Port Conflicts, assuming we are working with internal Fax/Modems:
  You can not skip COM-Ports when installing "COM using" devices.  For
  example, if your computer came with a COM1-IRQ4 and a COM2-IRQ3
  (very common) and you, now, buy a Fax/Modem; you can not configure
  your Fax/Modem for COM4.  You must put it on COM3-IRQ?(find and use an
  unused one) or disable COM2 on your IO-Board and configure your
  Fax/Modem for COM2-IRQ3.

  IRQ Conflicts present themselves when for example you have a mouse on
  COM1-IRQ4 (the proper configuration) and you configure your Fax/Modem
  for COM3-IRQ4.  Normally COM3 should/would use IRQ4; but it assumes that
  COM1 is not using IRQ4 and that nothing else is using IRQ4.  If this
  type of "IRQ Conflict" happens to you; simple set your Fax/Modem to:
  COM3 and use another UN-USED IRQ such as COM3-IRQ5, COM3-IRQ7,
  COM3-IRQ2.  IRQ4 is usually used on COM1 so you should *not*, normally,
  use COM3-IRQ4.  For details, read "FAX/MODEM INSTALLATION:" in the
  README.TXT.

  To configure your COM-Ports or Fax/Modem you will have to remove (or
  get a professional to) your device, get the manual and move jumpers or
  set DIP-switches.  For details on this subject, read the FaxMail for
  Windows "FAX/MODEM INSTALLATION:" section of the README.TXT.



 Q-24
  My Fax/Modem is *not* listed in the FaxMail for Windows installation
  Fax/Modem Selections.  I ran COMTEST1.COM and COMTEST2.COM.  I know
  that I chose the correct COM-IRQ yet when I read the CLASS1.TXT and
  CLASS2.TXT files, that they produced, I found that they only <O> to my
  Fax/Modem but did not <I> from the Fax/Modem.

  During installation I tried some to the other Fax/Modem-Drivers yet
  when I boot, the FaxMail for Windows Fax/Modem-Drivers will not load.

 A-24
  Some Fax/Modems do not have Fax capabilities built in their firmware.
  These Fax/Modems have programs that you load into them just before using
  them.  Before using the Fax/Modems, you select and load the appropriate
  PRE-FAX-PROGRAM and then load the Fax/Modem-Driver.  FaxMail for Windows
  puts its Fax/Modem-Driver on the first line in your AUTOEXEC.BAT;
  so you will have to move the line(s) that load the PRE-FAX-PROGRAM into
  your Fax/Modem ahead of the FaxMail for Windows Fax/Modem-Driver.  Read
  the next Question and Answer for a specific example.

 Q-25
  Digicom Connection 14.4+Fax or P. C. LOGIC FAX144C, FAX144DM

 A-25
  Unlike most Fax/Modems, {Digicom Connection 14.4+Fax} does not have
  its Class 1 capabilities in its firmware but rather it is loaded.
  The software to TRANSFORM this Fax/Modem into a CLASS 1 Fax/Modem
  come with the Fax/Modem.  It has to be loader each time you boot your
  computer and *BEFORE* you load the FaxMail for Windows Fax/Modem-Driver
  (FM_ROCK1.COM) that is found in your AUTOEXEC.BAT.  Because this
  installation places FM_ROCK1.COM in you AUTOEXEC.BAT on the first line,
  you will have to go into your AUTOEXEC.BAT and move the lines that load
  the TRANSFORMation software so it will be loaded before the
  FM_ROCK1.COM Fax/Modem-Driver.  When you are finished, your
  AUTOEXEC.BAT should look something like this:
Example 1:
 CD \SMODEM              {Change Directory to where Digicom keeps files
 DL FAX144C1.DSI         {Download Class 1 TRANSFORM software to Fax/Modem
 CD \                    {Change Directory back to the Root Directory
 C:\FAXMAIL\FM_ROCK1.COM {Load the FaxMail for Windows Fax/Modem-Driver
Example 2:
 CD \DMODEM              {Change Directory to where P. C. LOGIC keeps files
 DL FAX144C.CAR          {Download Class 1 TRANSFORM software to Fax/Modem
 CD \                    {Change Directory back to the Root Directory
 C:\FAXMAIL\FM_ROCK1.COM {Load the FaxMail for Windows Fax/Modem-Driver



 Q-26
  My GVC, FM-144HVBIS/R1, V1.61, won't work properly with any of the
  Fax/Modem-Drivers.

 A-26
  If you have a GVC, FM-144HVBIS/R1 and the version is below V2.00, call
  GVC Tech-Support at (201) 579-2954 and they will upgrade your Fax/Modem.

  To find out what "Model, Revision, Version" you have, run COMTEST1.COM
  or COMTEST2.COM included with FaxMail for Windows, read the CLASS1.TXT
  or CLASS2.TXT file that it generates and look for the following lines:

 <O> AT+FREV?                       }Ask Fax/Modem, what Factory Revision.
 <I> AT+FREV?                       }Fax/Modem echoes back (acknowledge).
 <I> FM-144HVBIS/R1  V1.61          }Model, Revision, Version. (Defective)
 <I> MODEM CHIP : ROCKWELL RC144DP  }Rockwell Class 2 Fax/Modem Chip.
 <I> FAX CLASS 2                    }Rockwell Class 2 Fax Support.
 <I> OK                             }Command processed ok.

  Note: The Version here is V1.61 witch is less than V2.00.  This customer
        needs an upgrade.

 Q-27
  My "Supra FAX Modem" does not work right.

 A-27
  Maybe you chose the wrong Fax/Modem-Driver.  Some Supras work best on
   "Supra FAX Modem, Class 1,2(1) -- FM_ROCK1.COM"
  and others work best on
   "Supra FAX Modem Plus, Class 1,2(2) -- FM_ROCK2.COM"

  If you feel you may need to change the Driver, look in your AUTOEXEC.BAT
  to see which you chose and then run Change Fax/Modem-Driver and choose
  the other when you get to the Fax/Modem-Driver selection Window.

 Q-28
  My "HP Deskjet 500C" takes 30 minutes per page to print a Fax. ! HELP !

 A-28
  The slowness is due to the "HP Deskjet 500C" Printer-Driver.

  Use the Microsoft Windows "HP Deskjet 500" Printer-Driver for printing
  Fax.  The suffix C stands for color.  Faxes are black and white and
  should only take about 30 seconds per page on the "HP Deskjet 500"
  Printer-Driver.



 Q-29
  Microsoft Word for Windows 2.0 sometimes shifts the image to the far right
  leaving most of the page blank and losing most of the image off the
  right side.

 A-29
  1. Toggle <PRINTER OR FAX TOGGLE> to PRINTER IS ACTIVE.
  2. Load Word for Windows.
  3. Open the document you intend to print.
  4. Toggle <PRINTER OR FAX TOGGLE> to FAX IS ACTIVE.
  5. Edit the document if you want to.
  6. Use the <CONVERT TO FAX> button.

 NOTE:
  You should toggle the <PRINTER OR FAX TOGGLE> to FAX IS ACTIVE before
  loading most Applications except Word for Windows 2.0.
  Microsoft Word for Windows version 6.0 does not have this bug.

 Q-30
  Microsoft Windows Write sometimes crashes when I try to <CONVERT TO FAX>.

 A-30
  1. Toggle <PRINTER OR FAX TOGGLE> to FAX IS ACTIVE.
  2. Load Windows Write.
  3. Open the document you intend to print.
  4. Edit the document if you want to.
  5. Use the <CONVERT TO FAX> button.

 NOTE:
  You should toggle the <PRINTER OR FAX TOGGLE> to FAX IS ACTIVE before
  loading most Applications except Word for Windows 2.0.

 Q-31
  Does the FaxMail for Windows Fax/Modem-Driver LH (LoadHigh)?

 A-31
  Yes, the "LH " tells your computer to load the Fax/Modem-Driver high:
 LH C:\FAXMAIL\FM_ROCK2.COM
  If you want them to load into conventional memory, remove the "LH "
  to make it look like this:
 C:\FAXMAIL\FM_ROCK2.COM

 Q-32
 Windows keeps asking if it should take control of the COM-Port that I
 have my Fax/Modem on?

 A-32
  Load the Windows Control Panel (found in "Accessories" Group or "Main"
  Group), select 386 Enhanced, high-light your COM-Port and select Never
  Warn.
           ( ) Always Warn.
           (*) Never Warn.
           ( ) Idle (in sec.)



 Q-33
 My Modem seems to have some sort of conflict while in Windows.

 A-33
 Check your Windows COM-IRQ setting.  Here is the step-by-step directions:
 Load <Control Panel (Found in Accessories on Main Group)>,
 <Ports>,
 select your port,
 <Settings>,
 <Advanced>,
 Set <Base I/O Port Address> to:
  If your Fax/Modem is on COM1, Set to: 03F8
  If your Fax/Modem is on COM2, Set to: 02F8
  If your Fax/Modem is on COM3, Set to: 03E8
  If your Fax/Modem is on COM4, Set to: 02E8
 Set <Interrupt Request> to:
  If your Fax/Modem is on COM1-IRQ4, Set to: 4
  If your Fax/Modem is on COM2-IRQ3, Set to: 3
  If your Fax/Modem is on COM3-IRQ5, Set to: 5
  If your Fax/Modem is on COM4-IRQ7, Set to: 7
  etc, etc, etc, etc, etc. . . . . . . . . .
 OK,
 OK,
 Close.



 Q-34
 List of Fatal Error Code meanings.

 A-34
 000 No_Err                 036 EstabConectSnd_Err3
 001 ATA_Err                037 EstabConectSnd_Err4
 002 Class1_NSF_Err         038 EstabConectSnd_Err5
 003 Class1_CSI_Err         039 EstabConectSnd_Err6
 004 Class1_DIS_Err         040 EstabConectSnd_Err7
 005 Class1_TSI_Err1        041 EstabConectSnd_Err8
 006 Class1_TSI_Err2        042 EstabConectSnd_Err9
 007 Class1_DCS_Err1        043 EstabConectSnd_Err10
 008 Class1_DCS_Err2        044 EstabConectSnd_Err11
 009 Class1_TCF_Err1        045 EstabConectSnd_Err12
 010 Class1_TCF_Err2        046 EstabConectSnd_Err13
 011 Class1_TCF_Err3        047 EstabConectSnd_Err14
 012 Class1_CFR_Err         048 WriteDCX_HeaderFXR_Err
 013 EstabConectRcv_Err     049 SaveRcvOrEventLog_Err1
 014 CreateRcvDCX_File_Err  050 SaveRcvOrEventLog_Err2
 015 RcvAnotherPage_Err     051 SaveRcvOrEventLog_Err3
 016 Find1stFF_Err          052 OpenCreateAppendQueFile08h_Err1
 017 GetAnotherT4Byte_Err   053 OpenCreateAppendQueFile08h_Err2
 018 WritePCX_Header_Err    054 UpDateUnqNum08h_Err
 019 RcvWasAborted_Err      055 SaveRcvOrEventLogFile08h_Err1
 020 GotAllThePgData_Err1   056 SaveRcvOrEventLogFile08h_Err2
 021 GotAllThePgData_Err2   057 CreateRcvDCX_File_Err1
 022 GotAllThePgData_Err3   058 CreateRcvDCX_File_Err2
 023 GotAllThePgData_Err4   059 CreateRcvDCX_File_Err3
 024 RcvBaudRate_Err        060 GetSndNowTaskAndUpDateQue_Err2
 025 AddCoverPage_Err       061 GetSndNowTaskAndUpDateQue_Err4
 026 AnotherPgProc_Err1     062 GetSndNowTaskAndUpDateQue_Err5
 027 AnotherPgProc_Err2     063 SaveRcvOrEventLogFile08h_Err3
 028 OpenFaxFileRd_Err      064 GetTheSendFile_Err1
 029 ReadFaxFileRd_Err      065 GetTheSendFile_Err2
 030 MPS_Err1               066 GetTheSendFile_Err3
 031 MPS_Err2               067 GetSndFutTaskAndUpDateQue_Err2
 032 EndItAllProc_Err       068 GetSndFutTaskAndUpDateQue_Err4
 033 EndOfSendTheFax_Err    069 GetSndFutTaskAndUpDateQue_Err5
 034 EstabConectSnd_Err1    070 DialThePhone_Err
 035 EstabConectSnd_Err2    071 BlindAnswer_Err

